Title

competitions

998cc, 1100cc & 998cc Cooper - To 1980

Label	Part No	Description	Quantity	Comments
1	12G123	Connecting rod number 2 and 4	2	N.L.A
1	12G126	Connecting rod number 1 and 3	2	N.L.A
2	2A660	Locktab	4
3	C-STR319	High-grade Big end bolt kit	1
3	12G2217	Big end bolt	8
4	8G2733	Crankshaft (forging number 12A595) (12A1451)	1	N.L.A - 998cc and Cooper
4	8G2732	Crankshaft (forging number 12G82) 1100cc	1	N.L.A
5	6K836	Crankshaft key	1
6	VP572-00	Con rod bearings (Mahle)	1	Std/10/20 only. Mahle was Vandervell
6	AEB572-00	Con rod bearings ACL Bearing	1	Std/10/20/30/40 oversize
6	VC1017-00	Con rod bearings Mahle race	1	Std/10
7	VP733-00	Mains bearings (Mahle)	1	Std/10/20 only. Mahle was Vandervell
7	AEM3314-00	Mains bearings ACL Bearings	1	Std/10/20/30/40 oversize
7	VM1018-00	Mains bearings Mahle race	1	Std/10
8	AEW2122-00	Thrust washer set	1	Std/3 thou oversize
9	22A1493	Primary gear (24 teeth)	1
10	DAM8887	Bush front was 22G401	1
11	22G109	Bush rear	1
12	22A321	Thrust washer 2.79-2.84mm (.110-112”) - N.L.A	1	These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G549 for wear.
12	22A322	Thrust washer 2.84-2.89mm (.112-114”)	1	These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G549 for wear.
12	22A323	Thrust washer 2.89-2.94mm (.114-116”)	1	These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G549 for wear.
12	22A324	Thrust washer 2.94-2.99mm (.116-118”)	1	These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G549 for wear.
12	22A450	Thrust washer 2.99-3.04mm (.118-120”)	1	These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G549 for wear.
12	22A451	Thrust washer 3.04-3.09mm (.120-122”)	1	These shims are used to give the correct end float of 3-6 thou on the primary gear check 22A319 and 88G549 for wear.
13	22A319	U Clip thrust	1
14	88G549	Backing ring	1
15	AEA630	Camshaft 1100cc and 998 Cooper	1	1/2” wide lobe was 12G165 C.W.E
15	8G712	Camshaft 998cc	1	N.L.A
16	2A299	Camshaft oil pump drive	1	N.L.A (Fitted in camshaft new)
17	WKN505	Camshaft key pin	1
18	AHU2379	Camshaft plate	1
19	GFK5179	Locating plate bolt	3	1/4”UNF 3/4”long
20	GHF321	Locating bolt shake proof washer	3
21	2A85	Camshaft gear with tensioners	1	N.L.A use 12G4337
22	8G549	Tensioner rubber rings	2
23	12G4337	Camshaft gear, fitted originally without tensioner	1
24	12G2621	Tensioner, fits 12G2626 front plate only	1	From engine number 99H791, 10H791 Not 998 Cooper
25	12G2628	Tensioner mounting plate	1
26	12G2629	Pivot pin	1
27	2A759	Camshaft locktab	1
28	6K629	Camshaft nut	1
29	8G725	Crankshaft gear	1
30	6K628	Washer to shim crank gear	1
31	3H2127	Timing chain (Simplex)	1
32	2A970	Front plate - pre tensioner type	1	N.L.A
32	12G2626	Front plate - used with tensioner pads	1
33	12G619B	Gasket for 2A970 front plate	1	For gasket sets see page 28
34	12G4499	Distributor drive spindle	1	C.W.E
35	13H2792	“O” ring distributor housing	1
36	12A1136	Housing	1	N.L.A
37	2A14	Push rod	8	See C-AEG581 alternative
38	2A13	Cam follower	8	Alternative to AEG584
38	AEG584	Cam follower with oil hole	8	Alternative to 2A13

Previous | Next | Index

Contact Mini Spares

Store Details:

Classic Mini Brochure & Manuals

Mini Spares Online Documents