| Label |
Part No |
Description |
Quantity |
Comments |
|
| 1 |
12G123 |
Connecting rod number 2 and 4 (circlip type) |
2 |
N.L.A |
|
| 1 |
12A1997 |
Connecting rod number 2 and 4, press fit gudgeon pin |
2 |
N.L.A - 1985 on (piston has no circlips) |
|
| 2 |
12G126 |
Connecting rod number 1 and 3 (circlip type) |
2 |
N.L.A |
|
| 2 |
12A1999 |
Connecting rod number 1 and 3, press fit gudgeon pin |
2 |
N.L.A - 1985 on (piston has no circlips) |
|
| 3 |
2A660 |
Locktab, deleted when CAM6126 fitted |
4 |
Deleted after 1981 |
|
| 4 |
CAM6126 |
Connecting rod bolt, replaced 12G2219 |
1 |
See C-STR319 |
|
| 5 |
BHM1436 |
Crankshaft, 8G2733 fitted until 1984 |
1 |
N.L.A |
|
| 6 |
6K836 |
Crankshaft keyway |
1 |
|
|
| 7 |
VP572-00 |
Con rod bearings (Mahle) |
1 |
Std/10/20 only. Mahle was Vandervell |
|
| 7 |
AEB572-00 |
Con rod bearings ACL bearing |
1 |
Std/10/20/30/40 oversize |
|
| 7 |
VC1017-00 |
Con rod bearings Mahle race |
1 |
Std/10 |
|
| 8 |
VP733-00 |
Main bearing, locating lug on edge of both halves was 8G2332. |
1 |
Pre 1985 (Mahle) - Std/10/20 only. Mahle was Vandervell |
|
| 8 |
AEM3314-00 |
Main bearing, locating lug on edge of both halves. ACL Bearings |
1 |
Pre 1985 - 10/20/30/40 oversize |
|
| 8 |
AEM3427-00 |
Main bearing (centre locating lip) 1985 on |
1 |
Was BHM1573/VP918855 (ACL) Std/10/20 only |
|
| 9 |
AEW2122-00 |
Thrust washer set |
1 |
Std/3 thou oversize |
|
| 10 |
22A1493 |
Primary gear (24 teeth), old type |
1 |
|
|
| 10 |
DAM8888 |
Primary gear (29 teeth), A plus |
1 |
|
|
| 11 |
DAM8887 |
Front bush, was 22G401 |
1 |
|
|
| 12 |
22G109 |
Bush rear |
1 |
|
|
| 13 |
22A321 |
Thrust washer 2.79-2.84mm (.110-112”) - N.L.A |
1 |
These shims are used to give correct end float of the primary gear which is 3-6 thou. Also check 22A319 & 88G549 for wear. |
|
| 13 |
22A322 |
Thrust washer 2.84-2.89mm (.112-114”) |
1 |
These shims are used to give correct end float of the primary gear which is 3-6 thou. Also check 22A319 & 88G549 for wear. |
|
| 13 |
22A323 |
Thrust washer 2.89-2.94mm (.114-116”) |
1 |
These shims are used to give correct end float of the primary gear which is 3-6 thou. Also check 22A319 & 88G549 for wear. |
|
| 13 |
22A324 |
Thrust washer 2.94-2.99mm (.116-118”) |
1 |
These shims are used to give correct end float of the primary gear which is 3-6 thou. Also check 22A319 & 88G549 for wear. |
|
| 13 |
22A450 |
Thrust washer 2.99-3.04mm (.118-120”) |
1 |
These shims are used to give correct end float of the primary gear which is 3-6 thou. Also check 22A319 & 88G549 for wear. |
|
| 13 |
22A451 |
Thrust washer 3.04-3.09mm (.120-122”) |
1 |
These shims are used to give correct end float of the primary gear which is 3-6 thou. Also check 22A319 & 88G549 for wear. |
|
| 14 |
22A319 |
Thrust washer U clip |
1 |
|
|
| 15 |
88G549 |
Backing ring |
1 |
|
|
| 16 |
CAM6267 |
Camshaft, 99H/B83P/B85P/D83P/E22 |
1 |
N.L.A - LC engine 2 rings between lobes 3&4 |
|
| 16 |
CAM4717 |
Camshaft, 99H/B81P/B82P/D80P/D81P/D82P/E20/E21 |
1 |
N.L.A - HC engine 1 ring between lobes 5&6 |
|
| 16 |
12G2983 |
Camshaft A plus early - No identification marks, mainly 1275cc |
1 |
N.L.A |
|
| 17 |
WKN505 |
Camshaft key |
1 |
|
|
| 18 |
AHU2379 |
Camshaft locating plate |
1 |
|
|
| 19 |
GFK5179 |
Locating plate bolt |
3 |
|
|
| 20 |
GHF321 |
Locating bolt shake proof washer |
3 |
|
|
| 21 |
12G4337 |
Camshaft gear |
1 |
|
|
| 22 |
12G2621 |
Tensioner pad |
1 |
|
|
| 23 |
12G2628 |
Tensioner mounting plate |
1 |
|
|
| 24 |
12G2629 |
Tensioner pin |
1 |
|
|
| 25 |
6K629 |
Camshaft nut |
1 |
|
|
| 26 |
2A759 |
Locktab |
1 |
|
|
| 27 |
CAM4700B |
Front plate gasket |
1 |
For gasket sets see page 28 |
|
| 28 |
12G2626 |
Front plate |
1 |
|
|
| 29 |
GFK5184 |
Bolt for plate to block |
2 |
|
|
| 30 |
GFK1125 |
Spring washer |
2 |
|
|
| 31 |
8G725 |
Crankshaft gear |
1 |
|
|
| 32 |
6K628 |
Crank gear shim washer |
1 |
Use as required |
|
| 33 |
3H2127 |
Timing chain |
1 |
|
|
| 34 |
12G3560 |
Distributor drive spindle |
1 |
N.L.A |
|
| 35 |
TAM1671 |
Distributor retaining plate was 613867A, pre 1985 |
1 |
|
|
| 36 |
TAM1706 |
Retainer screw 3/8”UNF 1”long, was CAM6105 |
1 |
N.L.A can use GFK5191 |
|
| 37 |
2A14 |
Push rod |
8 |
See C-AEG581 |
|
| 37 |
C-AEG581 |
Push rod (3 piece) performance use |
8 |
|
|
| 38 |
2A13 |
Cam follower without hole |
8 |
Alternative to AEG584 |
|
| 38 |
AEG584 |
Cam follower with hole |
8 |
Alternative to [LINK]2A13[LINK] |
|