Some Safari browsers are failing to connect secured pages Try the following: - refresh the page a few time to see if the page loads, if this fails please update the browser or try to browse the page in Firefox or Chrome. - Read more.
Minispares.com uses cookies to give a better browsing experience. Read more 
C-AHT348RACE

ALLOY 5 PORT RACE HEAD 37x31mm for std and.020" engines only

Very Hi spec all new alloy 5 port super gas flowing head. Outright sale to save you the risk of loosing £240 on exchange schemes where old heads are traded in and where faults can be found, especially by some companies.





C-AHT348RACE alloy cylinder head is de shrouded for use on std / 0.020” but will see a performance gain over the C-AHT347RACE when used on any 1275cc – 1380cc engine. Best head in the market for value and performance



Speak to NEIL BOOTH or Richard at York branch for all modifications required to fit this head as it is not a straight swop. Valve seat spacing means that a modification to the rocker cover is required and push rods are at a slight angle so check for clearance. Roller rockers are required to ensure pads are seated correctly on valves using C-AEG593 spacers alignment kit. A modified rocker cover is usually required and available as FP24 which has back machined to clear rockers. Manifold studs with UNC thread for alloy type heads only are included (6 of 53K547)

Mini Spares large valve alloy race ported and gas flowed head has race quality valves with special beryllium valve seats and special colsibro guides similar to those used on 8 port. Valves are spaced further apart to eradicate heat transfer causing cracking as found on old original cast heads. Weight approx 5.7kg.

Casting shape and profile is based on the 12G1805 "S" 940 casting design.

Machined for C-AEA526 height springs with our locating shims underneath.

With 37mm inlet and 31mm exhaust valves and titanium top caps plus 88G459EVO collets for ultimate strength. Combustion chambers are original 21.3 to 21.5cc

Advantages are weight and better cooling on a brand new head as old castings are becoming poor for reliabillty when modifying.

All heads are hipped and heat treated (annealed)from the foundry and pressure tested before machining and again after they are assembled but good quality flat head washers should be used.See C-AHT280

Use GEG300,TAM1521(BK450) or C-AHT189 cometic head gaskets only

Ring Mini Spares North for technical information and availablity of any special requirements if we can be of assistance.

Where the inlet ports are opened up tubes are put in to give full flow benefit. Suggested torque setting procedure in workshop manual sequence as follows

1st stage 15lbs/ft

2nd stage 30lbs/ft

3rd stage 40lbs/ft

final stage 45lbs/ft ===if using copper head gasket you can re torque to 45lbs but there is no need on cometic or multi layer steel type head gaskets.
  • £2,317.50 exc vat
  • £2,781.00 inc vat

 Out of stock


Watch Product Email
 
 
  • share
 

Recommended products

Showing 1 to 0 of 0 products
COMPETITION HEAD STUD AND NUT KIT
C-AHT280   More Details


Was £69.00
(inc VAT) £82.80

HEAD GASKET COPPER PERFORMANCE 1275. MINISPAR......
GEG300   More Details


Was £17.70
(inc VAT) £21.24

ROCKER COVER SILICON GASKET 11 STUD HEAD
GUG5038EVO   More Details


Was £8.75
(inc VAT) £10.50

 

This kit contains

Showing 1 to 0 of 0 products
VALVE SPRINGS RISING RATE UP TO 515 THOU LIFT......
C-AEA526   More Details


Was £29.40
(inc VAT) £35.28

VALVE INLET 37.2mm 1.464" race quality
C-AHT55   More Details


Was £21.39
(inc VAT) £25.67

CLUTCH CASE STUD SHORT 3 REQUIRED
53K547   More Details


Was £0.59
(inc VAT) £0.71

VALVE EXHAUST LONG STEM 31mm. heat treated fo......
C-AEG107   More Details


Was £17.69
(inc VAT) £21.23

VALVE STEM OIL SEAL AS USED ON MPI MODELS
LJQ101160   More Details


Was £1.20
(inc VAT) £1.44

TOP CAP TITANIUM RACE SET(8) FOR C-AEA526/7
C-AEA530   More Details


Was £80.00
(inc VAT) £96.00

VALVE COTTER SINGLE GROOVE COMPETITION (1 UNI......
88G459EVO   More Details


Was £3.96
(inc VAT) £4.75

8 PORT EX SEAT FOR HEADS 2016 ON FROM NO 02-0......
C-AHT388   More Details


Was £12.79
(inc VAT) £15.35