Gearbox - Up-rating diffs and FDs

There’s a good selection of straight-cut final FDs available. Examine the FD table, and using information from

'Gearbox - Final dives, standard' and 'Gearbox - Formulae for car speed, etc.'

you can assess which would best suit your usage. Bear in mind that they’re noisy, make sure you select one that’ll fit your diff unit, and also consider that using drop gears will allow fine-tuning of the ratio where necessary. See

'Gearbox - Up-rating drop gears'

Gearbox - Up-rating diffs, FDs and ancillaries.

part numbers: C-BTA166, C-BTA167, DAM6624, BTA101, 2A7062, DAM5071, DAM6027, RPS1418, C-AJJ3385, C-22A1731, ...Read more

Clutch - Adjustment of operating linkage

This is one of those areas where there is more than one way to skin the cat - depending on who you speak to. This is the method I have used for eternity, which has been totally reliable and never had a problem with.

This only applies to non-Verto type clutches, as the Verto types are not adjustable. You just have to make sure all the operating linkage components are in good order.

First off, ensure your operating linkage is up to scratch. For details on this, see 'Engine transplants - Clutch and flywheel'.

Satisfied all is OK, you can proceed with setting the linkage up.

1 - Remove/disconnect clutch return spring.

2 - Undo throw-out nuts (15/16"AF nuts on outer end of plunger) lock nut and back nuts off away from clutch cover.

Engine transplants - Ancillary parts

Engine mountings are a whizz to fit as the Mini ones fit straight onto any of the other units. Just remove the Metro/AA/1300GT ones and swop the mounts over from the Mini unit. If they’re split, fit new ones, they’re cheap.

Terminology -
BBU - Big Bore Unit
SBU - Small Bore Unit

NOTE: This information covers transplanting large-bore engine units into small-bore engined Minis. For further information for exact differences between pre-A+ and A+ units, see relevant separate article.

Engine mountings and steady bars.
Engine mountings are a whizz to fit as the Mini ones fit straight onto any of the other units. Just remove the Metro/AA/1300GT ones and swop the mounts over from the Mini unit. If they’re split, fit new ones, they’re cheap. If using the AA/1300GT unit - it's advisable to cut off the 'wings' on the front plate that carried the engine mounts on the radiator end.

Engine transplants - Clutch and flywheel assemblies

To go in to all the possible permutations would take a few chapters on it’s own. Suffice to say that the Metro had a few weirdo fitments such as cable operation, an in-line ‘damper’ (some got fitted to Minis too - eek),

Terminology -
BBU - Big Bore Units
SBU - Small Bore Units

NOTE: This information is largely concerned with transplanting a large-bore engine into a small-bore engined Mini. For further information on clutch and flywheel assemblies in particular, refer to relevant separate article.

To go in to all the possible permutations would take a few chapters on it’s own. Suffice to say that the Metro had a few weirdo fitments such as cable operation, an in-line ‘damper’ (some got fitted to Minis too - eek), and ‘top-hat’ plunger and rod bearing operation.

Engine transplants - Clutch and flywheel assemblies

To go in to all the possible permutations would take a few chapters on it’s own. Suffice to say that the Metro had a few weirdo fitments such as cable operation, an in-line ‘damper’ (some got fitted to Minis too - eek),

Terminology -
BBU - Big Bore Units
SBU - Small Bore Units

NOTE: This information is largely concerned with transplanting a large-bore engine into a small-bore engined Mini. For further information on clutch and flywheel assemblies in particular, refer to relevant separate article.

To go in to all the possible permutations would take a few chapters on it’s own. Suffice to say that the Metro had a few weirdo fitments such as cable operation, an in-line ‘damper’ (some got fitted to Minis too - eek), and ‘top-hat’ plunger and rod bearing operation.

Suspension - Dampers, basic knowledge

The damper's job is very simple to explain - to keep the tyre in contact with the ground wherever and whenever possible...

Verto to Pre Verto,Clutch swap

TEST If converting from A plus verto type clutch to the original Diaphragm type these are the major components you will require:

All the major extra parts required to convert from Verto Clutch to Diaphragm type parts (in brackets indicate alternatives)

6 x GHF323 shakeproof washer 3/8” UNF
2 x GFK5240 bolt remote housing short 1” UNC
1 x 88G508 flywheel keyway – pre verto (EN24T)
6 x 2A3658 clutch flywheel strap
1 x 2A3601 clutch return spring anchor
1 x CLZ628 clutch arm pin – bottom
1 x CLZ518 clevis pin for clutch arm at the top
1 x 22A747 flywheel bolt pre verto
3 x 2A3657 clutch bolt long cover to pressure
3 x (C-2A3657 ) clutch bolt long cover to pressure

Donny Focus - BigMacRacing

Oulton Park was utterly frustrating – there were big hopes returning to a fantastic circuit the Mini 7 Club last visited in 2012. The Cheshire circuit really is a fantastic location, providing race driver a superb challenge...